manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 182

8.1.4

Derating factors

Given an ambient temperature > 40 °C or installation altitude > 1000 m above sea level, the 

permissible torques/powers must be determined with the factors from the following table. 
The factors refer to the static torque M

0

. Shift the S1 characteristic curve in parallel.

Table 8-2

Power derating depending on the installation altitude and the ambient temperature

Installation altitude above sea 

level in m

Ambient temperature in ° C

30

40

45

50

1000

1.05

1.00

0.97

0.94

2000

1.00

0.95

0.92

0.88

Calculate the derating value for ambient temperatures that are not shown here and installation altitudes 

below the maximum values by interpolating. For example: 40 °C at 1500 m above sea level = derating 

factor 0.975

8.1.5

Degree of protection

The degree of protection designation in accordance with EN 60034-5 (IEC 60034-5) is 

described using the letters IP and two digits (e.g. IP64). 
IP = International Protection

1st digit = protection against the ingress of foreign bodies

2nd digit = protection against water
DIN 60034-5 is valid for water as potentially occurring medium, not for oil or other creeping 

fluids. 
Configure the motor in the required degree of protection.

Degrees of protection available for the 1FK2
The 1FK2 motors are available with the following degrees of protection:
● IP64
● IP65 optional
The motors with IP65 degree of protection have a radial shaft seal.

1

Radial shaft sealing ring

Technical specifications
8.1 Technical data and properties of the motor

SINAMICS S210 servo drive system

180

Operating Instructions, 12/2017, A5E41702836B AA

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды