manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 136

6.7

Plant-specific settings

To make plant-specific settings, go to the "Parameter - Parameter list" menu and select the 

expanded view there.

6.7.1

Changing the direction of rotation of the motor

If you determine that the motor is rotating in the wrong direction, you can reverse the direction 

of rotation as described below.
1. Set p0010 to value 3 (motor commissioning).
2. Change the direction of rotation via p1821. 

– 0: Clockwise rotation
– 1: Counter-clockwise rotation

3. Reset p0010 to value 0 (ready).
4. If possible, check the new setting using the control panel.
5. Save the setting via 

.

This change takes effect in both the control panel and the PLC.

6.7.2

Electronic weight counterbalance for a vertical axis

With a vertical axis without mechanical weight compensation, you can set an electronic weight 

compensation by offsetting the torque limits (p1532). 
The torque limits (p1520 and p1521 - can also be set via "Parameter - Limits") are shifted by 

this offset.
The required offset value is displayed in r0031 during a standstill. Transfer this value to p1532.
Save the setting via 

.

To prevent the axis from dropping after the brake is released, you can specify the torque offset 

as an additional torque setpoint (M_ADD) via the supplementary telegram 750. As a result, 

the holding torque is specified immediately after the brake is released.

Note
Due to the specified supplementary torque setpoint via the controller, a switchover of the 

supplementary torque is also possible. Thus, when the product is lifted, a supplementary torque 

can be specified that is different from the supplementary torque for a movement without a load.

The supplementary telegram 750 must be configured in the PLC.

   Supplementary telegrams (Page 739)

Commissioning and diagnostics in the Web server
6.7 Plant-specific settings

SINAMICS S210 servo drive system

134

Operating Instructions, 12/2017, A5E41702836B AA

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды