Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 121

Страница: 121 / 768

6.5.2

Performing One Button Tuning

An important part of the basic commissioning is performed using "One Button Tuning" ("OBT").

In this way, the optimum controller settings of the converter can be quickly determined with

just a few entries.

Procedure

1. Select the "Optimization" submenu in the "Commissioning" navigation.

Figure 6-6

View before performing the One Button Tuning

2. Click "Take Control".

Confirm the "Activate master control" prompt.

The master control is indicated by a broken orange bar.

3. Select the desired dynamic response setting for the One Button Tuning corresponding to

the mechanical system of your machine.

One Button Tuning optimizes the drive based on the selected dynamic response setting.
– "Conservative":

Slow control – low mechanical load.

– "Standard":

Best compromise between fast speed control and low mechanical load.

– "Dynamic":

Fast speed control – high mechanical load.

Commissioning and diagnostics in the Web server

6.5 Commissioning

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

119

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SIMOTICS S-1FK2

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Результаты поиска

Содержание SIMOTICS S-1FK2

Отзывы:

Бренды по названию

Популярные бренды