Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 768

Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 108

6.1

Fundamentals

Accessing the web server

The web server is accessed per default via the service interface X127.
The service interface is designed for point-to-point connections and must not be networked.
The service interface has the following default setting:
● IP address: 169.254.11.22
● Subnet mask: 255.255.0.0
The interface can be assigned via DHCP or also another address (e.g. from an external WLAN

access point).
If you want to access the converter via WLAN from a mobile terminal device, connect a

commercially available WLAN access point to the service interface. Refer to the description

of the device on how to configure the access point.
Access via PROFINET

Configuring the IP connection (Page 158)

The IP addresses of the service and PROFINET interfaces must not be in the same subnet.

Preparations

1. Install the motor and converter according to the specifications in the following section:

Installing (Page 83)

2. Mount the motor on the mechanical system. Connect the motor to the converter.
3. Connect the converter to your commissioning device via the service interface (X127).
4. Switch the converter on.

The converter powers up and reads the motor data.

5. Start the browser for commissioning.
6. Enter the IP address of the converter in the input line of your browser.

Default IP address: 169.254.11.22.

Interfaces and connection type

Using the default configuration of the web server, you can access the SINAMICS frequency

converter using the service interface (X127) - both via an HTTP connection as well as via an

encrypted HTTPS connection.
In the standard configuration, interface X150 is deactivated for web server access operations.

If the X150 interface is activated for access to the web server, then access takes place

automatically via a secure HTTPS connection.
For details on this, see:

Commissioning and diagnostics in the Web server
6.1 Fundamentals

SINAMICS S210 servo drive system

106

Operating Instructions, 12/2017, A5E41702836B AA

«
...
106
107
108
109
110
...
»

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды