Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 95

Страница: 95 / 188

● In the case of aluminum connecting bars, insert a steel washer between the cable lug and

the connecting bar. This prevents contact corrosion.

● Correctly close and seal threads or holes that are not being used ensuring that the IP degree

of protection is maintained. The IP degree of protection is specified on the rating plate.

Replace the cable glands that are not being used by appropriately certified screw plugs.

6.5.5

Connecting cables with cable lugs

1. Select the cable lugs according to the required cable cross-section and fixing screw or stud

size. Information about the maximum cross-section for the respective standard terminal

box design can be found in the catalog.

A sloped/angular arrangement of the supply cables is only permitted provided the required

minimum air clearances are met.

2. Remove the insulation from the conductor ends so that the remaining insulation reaches

almost up to the cable lug

①

. Connect only one conductor per cable lug.

3. Fasten the cable lug to the end of the conductor correctly, e.g. by squeezing.

Figure 6-9

Connection with cable lug and fixing screw (schematic diagram)

4. Insulate the cable lug sleeves where necessary to ensure minimum air clearances and the

creepage distance are maintained.

5. Place the cable lug on the terminal support. If you are using a disconnecting link, check its

positioning.

For terminal boxes 1XB7740 and 1XB7750, place the cable lug on the busbar.

6. Tighten the fixing element

②

with the corresponding tightening torque:

Fixing element

Tightening torque

Fastening screw M12

20 Nm

Fixing screws M16

40 Nm

Fixing nuts M12

20 Nm

Note
You can find more information in Chapter 2 of catalog D81.8.

Electrical connection

6.5 Inserting and routing the cables

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды