Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 188

background image

5.2.2

Checking the load handling attachments

Inspect the load handling attachments such as the load trestles, lifting eyes and ring bolts and

also the lifting gear, before lifting the machine:
● Inspect the load handling attachments on the machine for possible damage. Replace any

load suspension equipment that is found to be damaged.

● Before use, check that the load suspension equipment is correctly attached.
● When lifting the machine, use only approved and undamaged lifting gear of sufficient rated

capacity. Check the lifting gear prior to its use.

WARNING

The machine can be dropped
If the load handling attachments and lifting gear are damaged or not correctly secured,

the machine may be dropped during lifting. This can result in death, serious injury or

material damage.
● Inspect the load handling attachments and lifting gear before use.

5.2.3

Removing the rotor shipping brace

If a rotor shipping brace is attached to the machine, remove it at the last possible moment,

for example, when you are ready to push on the output or drive element.

5.2.4

Removing the rotor shipping brace from machines in vertical type

NOTICE
Removing the rotor shipping brace in the horizontal position.
Dismantling the rotor shipping brace when the machine is in a horizontal position could

damage the bearings.
● Only remove the rotor shipping brace when the machine is in a vertical position.

NOTICE
Turning the motor over without rotor shipping brace
Failure to fit the rotor shipping brace can result in damage to the bearings while the machine

is being turned onto its side.
● Fix the rotor in place before you turn the machine into a horizontal position.

Assembly

5.2 Lift the machine to where it will be installed, and position it

SIMOTICS FD 1MH1

Operating Instructions 08/2017

65

«
...
63
64
65
66
67
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Бренд: TAARKS Страницы: 7

Бренд: Daedong Страницы: 51

Бренд: O.S. engine Страницы: 15

Бренд: ZAFFER Страницы: 28

Бренд: Applied Motion Products Страницы: 2

Бренд: Bosch Страницы: 20

Rexroth Hagglunds CA 10

Бренд: Bosch Страницы: 53

Бренд: Bosch Страницы: 60

Бренд: Bosch Страницы: 74

Rexroth Hagglunds CA 100

Бренд: Bosch Страницы: 76

Rexroth 70 Series

Бренд: Bosch Страницы: 56

Rexroth IndraDyn T

Бренд: Bosch Страницы: 76

Rexroth A10VER 52 Series

Бренд: Bosch Страницы: 56

Бренд: Bosch Страницы: 48

Бренд: Bosch Страницы: 114

Бренд: Bosch Страницы: 72

Rexroth A6VM series 71

Бренд: Bosch Страницы: 76

Rexroth Hagglunds VI 44 Series

Бренд: Bosch Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды