Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 188

background image

5.1

Preparations for installation

5.1.1

Requirements for installation

The following requirements must be satisfied prior to starting installation work:
● Staff have access to the operating and installation instructions.
● The machine is unpacked and ready for mounting at the installation location.

Note
Measure the insulation resistance of the winding before starting installation work
Measure the insulation resistance of the winding before starting any installation work. If the

insulation resistance lies below the specified value, take appropriate remedial measures.

These remedial measures may necessitate the machine being removed again and

transported.

NOTICE
High temperatures
The motor components get very hot during operation. High temperatures can damage parts

mounted by customers, such as cables manufactured out of materials that are not heat

resistant.
● Temperature-sensitive parts must not come in contact with or be attached to components

mounted on the machine.

● Only use heat-resistant mounting parts. The connecting cables and cable entries must be

suitable for the particular application.

5.1.2

Insulation resistance and polarization index

Measuring the insulation resistance and polarization index (PI) provides information on the

condition of the machine. It is therefore important to check the insulation resistance and the

polarization index at the following times:
● Before starting up a machine for the first time
● After an extended period in storage or downtime
● Within the scope of maintenance work
The following information is provided regarding the state of the winding insulation:
● Is the winding head insulation conductively contaminated?
● Has the winding insulation absorbed moisture?

Assembly
5.1 Preparations for installation

SIMOTICS FD 1MH1

60

Operating Instructions 08/2017

«
...
58
59
60
61
62
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Бренд: Valor Страницы: 97

Бренд: Atlas Copco Страницы: 156

Бренд: Schartec Страницы: 16

Бренд: Generac Power Systems Страницы: 124

Бренд: ZAFFER Страницы: 28

Бренд: Northern Lights Страницы: 42

Бренд: Chicago Electric Страницы: 8

Бренд: Lycomin Страницы: 171

CROUZET 801400TNI21

Бренд: Innovista Sensors Страницы: 39

Бренд: YS Страницы: 2

Бренд: MULTIPLEX modell Страницы: 11

Бренд: Honda Страницы: 133

Бренд: Golden Eagle Страницы: 11

Бренд: Mitsubishi Heavy Industries Страницы: 111

Бренд: O.S. engine Страницы: 40

Бренд: Iveco Страницы: 42

Бренд: HRW Страницы: 23

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды