manualshive.com logo in svg

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

"Siemens SIMOTICS FD 1LL1" - Мощный и надежный электродвигатель для промышленных целей. Здесь вы найдете операционные и установочные инструкции в бесплатном скачивании на нашем сайте. Основные фокусы - качество и надежность. Скачайте свой руководство сейчас с manualshive.com.

Поделиться
Скачать
background image

See also

Safety information (Page 15)

4.18.1

Checking the delivery

The components are assembled on an individual basis. When you take receipt of the delivery, 

please check immediately whether the scope of the delivery matches up with the 

accompanying documents. No claims relating to defects/items missing from the delivery will 

be accepted if they are submitted at a later date.  
● Report any apparent transport damage to the delivery agent immediately.
● Immediately report any apparent defects/missing components to your contact partner.
These Operating Instructions are part of the scope of delivery; keep them in a location where 

they can be easily accessed.

4.18.2

Lifting and transportation

To safely lift and transport the machine, the following requirements must be met: 
● Personnel operating cranes and fork-lift trucks must be appropriately qualified.
● If the machine is packed, depending on the weight, size and on-site conditions, lift crates 

and transport frames using a fork-lift truck or a crane with slings. Use a crane or fork-lift 

truck suitable for the load.

● When lifting the machine, use only approved and undamaged sling guides and spreaders 

of sufficient rated capacity. Check the lifting equipment prior to its use. The weight of the 

machine is shown on the rating plate.

● When lifting the machine, refer to the information on the lifting plate.

– Comply with the specified spreading angles.
– Do not exceed the maximum lifting acceleration and lifting speed specified on the lifting 

plate. Lift the machine without jerking it.

Acceleration a ≤ 0.4 g (≈ 4 m/s

2 

)

Velocity v ≤ 20 m/min

WARNING

Transport for a different type of construction
If you do not transport or lift the machine in a position appropriate for its construction, the 

machine can tip, slip into the lifting equipment or fall down. This can result in death, serious 

injury or material damage.
● Use only the load carrying device on the stator frame for lifting.
● Use the load carrying device appropriate for the machine position.  
● Only use suitable rope guiding or spreading devices. 

Preparations for use

4.18 Transport and storage

SIMOTICS FD  1MH1

Operating Instructions 08/2017

45

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Wacker Neuson M1500 Operator'S Manual preview
M1500
Бренд: Wacker Neuson Страницы: 44
FAAC T-MODE TM 45 E Manual preview
T-MODE TM 45 E
Бренд: FAAC Страницы: 22
Westerbeke FOUR-60 Technical Manual And Parts List preview
FOUR-60
Бренд: Westerbeke Страницы: 140
CAB ROLLY RO.40 Instructions Manual preview
ROLLY RO.40
Бренд: CAB Страницы: 16
Toyama marine TM.5.8TS User Manual preview
marine TM.5.8TS
Бренд: Toyama Страницы: 88
Toro 303447 Troubleshooting Manual preview
303447
Бренд: Toro Страницы: 37
Lycoming AIO-360 Series Operator'S Manual preview
AIO-360 Series
Бренд: Lycoming Страницы: 155
O.S. engine FF-320 Owner'S Instruction Manual preview
FF-320
Бренд: O.S. engine Страницы: 17
O.S. engine 49-PI II Instruction Manual preview
49-PI II
Бренд: O.S. engine Страницы: 20
Volvo TAMD74C Operator'S Manual preview
TAMD74C
Бренд: Volvo Страницы: 88
Coleman EX300D52010 Parts Manual preview
EX300D52010
Бренд: Coleman Страницы: 24
Jonsered 581827101 Operator'S Manual preview
581827101
Бренд: Jonsered Страницы: 156
NANOTEC PD4-E Technical Manual preview
PD4-E
Бренд: NANOTEC Страницы: 295
DANA 4360-8 Parts List preview
4360-8
Бренд: DANA Страницы: 2
DANA 4360-78 Parts List preview
4360-78
Бренд: DANA Страницы: 3
DANA 4360-59 Parts List preview
4360-59
Бренд: DANA Страницы: 3
DANA 4360-77 Parts List preview
4360-77
Бренд: DANA Страницы: 3
DANA 4360-80 Parts List preview
4360-80
Бренд: DANA Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды