Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 33

Страница: 33 / 188

Preparations for use

Good planning and preparation of machine applications are essential in terms of keeping

installation simple and avoiding errors, ensuring safe operation, and allowing access to the

machine for servicing and corrective maintenance.
This chapter outlines what you need to consider when configuring your plant in relation to this

machine and the preparations you need to make before the machine is delivered.

4.1

Safety-related aspects to consider when configuring the plant

A number of residual risks are associated with the machine. These are described in the chapter

titled "Safety information" (Page 15) and in related sections.
Take appropriate safety precautions (covers, barriers, markings, etc.) to ensure the machine

is operated safely within your plant.

4.2

Observing the operating mode

Observe the machine's operating mode. Use a suitable control system to prevent overspeeds,

thus protecting the machine from damage.

4.3

Ensuring cooling

Ensure that the machine and/or any mounted external fan unit is sufficiently cooled by the

cooling air flow at the installation site:
● The cooling air can flow in and out freely. The full air flow provided by the fan is only achieved

if air can freely enter the impeller. Ensure that the required distance in accordance with the

dimensioned drawing is maintained.

● Hot discharged air must not be drawn in again.
● On the vertical design with air intake from above, the air inlets must be protected against

the ingress of foreign bodies and water.

4.4

Configuration of the cooling circuit and coolant supply

4.4.1

Material selection for the cooling circuit

For optimum durability of the cooling system, use a closed or half open cooling circuit in

stainless steel or acrylic butadiene styrene (ABS).

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды