Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 147

Страница: 147 / 188

9.2.2

Screws with preCOTE coating

The motor can partly be fitted with screws with preCOTE coating. To ensure screw locking,

use new screws with preCOTE coating during assembly/repair. As an alternative, use normal

screws with a threadlocker such as Loctite.

9.2.3

Roller-contact bearings

9.2.3.1

Removing roller bearing

Preparation

● Remove any grease feeders, shock pulse measurement equipment and possibly mounted

instrumentation at the DE and NDE.

● Ensure that the DE shaft extension is freely accessible. Remove the coupling.

Note
For a schematic diagram of the respective component layout, see the chapter "Spare

parts (Page 155)".

Procedure

1. Remove the components of the bearing mounting.

– Dismount the outer bearing cover.

If present: Remove the V ring (Page 148).

Uninstall the labyrinth sealing ring (only for the option "Increased degree of

protection") (Page 148).

– Ensure that the inner bearing cover is no longer attached to the bearing housing or end

shield.

There may be springs in the inner bearing cover.

– Support the rotor for the uninstallation of bearing housing or end shield.
– If necessary, remove the bearing housing from the end shield.
– Remove the end shield. Dependent on shaft height, roller bearing type and design, it is

either a bearing head design or a bearing housing design.

– Remove the locking ring from the shaft or the set screw, depending on the version.

2. Pull off the roller bearing together with the grease slinger.

Maintenance

9.2 Corrective Maintenance

SIMOTICS FD 1MH1

Operating Instructions 08/2017

147

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды