Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 142

Страница: 142 / 188

Regreasing roller bearings

Pay attention to the instructions on the lubricant plate.
1. Rotate the shaft when regreasing, so that the new grease can be distributed throughout

the bearing.

Motors that are operated with converters: Regrease the bearings at a low to medium speed

min

= 250 rpm, n

max

= 3600 rpm) to ensure an even distribution of grease.

WARNING

Rotating components
The shaft must rotate to allow the grease to be distributed. This can result in death, serious

injury or material damage.
● When regreasing, pay attention to all rotating components.

2. Clean the grease nipple before regreasing. Gradually press in an appropriate type and

amount of grease, as stamped on the lubricant plate and specified in these operating

instructions.

The roller bearing temperature rises sharply at first, then drops to the normal value again

when the excess grease is displaced out of the bearing.

3. The used grease collects outside each bearing in a spent grease chamber.

Lubricating roller bearings prior to commissioning
When properly stored prior to commissioning for a longer period of time, normally the grease

in the bearings does not deteriorate within two years. Please note the information regarding

long-term storage.
When commissioning, the bearings must be relubricated with twice the amount of lubricating

grease. When doing this, the shaft must rotate so that the grease is replaced in the bearings.

9.1.10

Sealing the rolling-contact bearings ("Increased degree of protection" option)

Relubricating the grease tank

In order to achieve optimum sealing of the rolling contact bearings and to reliably seal the

labyrinth joints with grease, the chamber must be relubricated at regular intervals. The

procedure is the same as that for lubricating grease. The sealing effect during operation is

optimum as long as a small amount of relatively clean grease is forced out.

Regreasing intervals

The necessary relubrication intervals depend essentially on the level of dirt in the environment

and on the ON time of the motor. For this reason, they can only be defined taking into account

the respective operating conditions. Make sure that the groove in the seal is full of grease at

all times.

Maintenance
9.1 Inspection and maintenance

SIMOTICS FD 1MH1

142

Operating Instructions 08/2017

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды