Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 188

background image

NOTICE
Machine damage caused by foreign bodies
Foreign bodies such as dirt, tools or loose components, such as screws etc., can be left by

accident inside the machine after maintenance is performed. These can cause short circuits,

reduce the performance of the cooling system or increase noise in operation. They can also

damage the machine.
● When carrying out maintenance work, make sure that no foreign bodies are left in or on

the machine.

● Securely attach all loose parts again once you have completed the maintenance

procedures.

● Carefully remove any dirt.

Note
Operating conditions and characteristics can vary widely. For this reason, only general

intervals for inspection and maintenance measures can be specified here.

WARNING

Risk of explosion due to static charging
If you clean the machine with compressed air, plastic components may become statically

charged and create a potentially explosive atmosphere. An explosion can occur. This can

result in death, serious injury or material damage.
● Do not use compressed air to clean plastic parts in an explosive atmosphere.
● When cleaning the machine, make sure that the air in the vicinity of the machine is free

of gas and dust.

9.1.2

Measuring the insulation resistance during the course of maintenance work

Measuring the insulation resistance and polarization index (PI) provides information on the

condition of the machine. It is therefore important to check the insulation resistance and the

polarization index at the following times:
● Before starting up a machine for the first time
● After an extended period in storage or downtime
● Within the scope of maintenance work
The following information is provided regarding the state of the winding insulation:
● Is the winding head insulation conductively contaminated?
● Has the winding insulation absorbed moisture?

Maintenance

9.1 Inspection and maintenance

SIMOTICS FD 1MH1

Operating Instructions 08/2017

135

«
...
133
134
135
136
137
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Бренд: Painless Performance Страницы: 24

Бренд: Westerbeke Страницы: 60

Бренд: Kubota Страницы: 285

Бренд: Briggs & Stratton Страницы: 10

Sonesse Ultra 50 DC RS485

Бренд: SOMFY Страницы: 16

Reliance CDX7150

Бренд: Baldor Страницы: 32

MAX-15CV-R Series

Бренд: O.S. engine Страницы: 34

Бренд: O.S. engine Страницы: 34

Бренд: O.S. engine Страницы: 40

AUTOMATE MT01-2101-069002

Бренд: rollease acmeda Страницы: 30

Concept engines

Бренд: RB Страницы: 19

Бренд: Vetus Страницы: 156

Бренд: Vetus Страницы: 84

Бренд: RENNTECH Страницы: 18

Бренд: ZLTECH Страницы: 26

Бренд: Bosch Страницы: 264

Бренд: Bosch Страницы: 68

Бренд: Bosch Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды