background image

Securing functional safety 

 

2.3 Electrical installation  of the encoder 

 

BA 2730 

14

 

Operating Instructions, 02/2021, A5E36448105A/RS-AG 

Connection assignment incremental encoder IN 8.5834 

 

 

Connector viewed from 

the outside 

 

Signal 

Diagram showing the signals for clockwise 

shaft rotation when viewing the clamping ring 

and/or the motor drive end. 

 

Power supply 

Incremental signals 

Connection 

U

P

 

Sensor U

P

 

O V 

Sensor O V 

A+ 

A- 

B+ 

B- 

Flange socket 

12  2 

10 

11 

 

Sensor pins jumpered 

in the encoder 

Sensor pins jumpered 

in the encoder 

Connection assignment, absolute encoder IA 8.5883 

 

 

Connector viewed from 

the outside 

 

Signal 

 0 absolute position value 

 Increasing absolute values 

Diagram showing the signals for 

clockwise shaft rotation when viewing 

the clamping ring and/or the motor 

drive end 

 

Power supply 

Incremental signals 

Connection 

U

P

 

Sensor U

P

 

O V  Sensor O V  Inner shield  A+  A- 

B+  B- 

Flange socket (SSI)  7 

10 

11 

15  16  12  13 

 

Sensor pins 

jumpered in the 

connector 

Sensor pins 

jumpered in the 

connector 

Not available  - 

 

 

 

Absolute position values 

Other signals 

Connection 
 

DATA  DATA, 

negated 

CLOCK  CLOCK, 

negated 

Direction of rotation  Zeros 

D+ 

D- 

C+ 

C- 

DIR 

SET 

Flange socket (SSI)  14 

17 

 

Absolute values are 

counted down when 

the input is 

energized. 

The absolute value 

is set to zero when 

the input is 

energized. 

 

Содержание SIMOGEAR BA 2730































Отзывы: