Siemens SIMOCODE 3UF Скачать руководство пользователя страница 109

Страница: 109 / 172

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

109

Logic Modules

13.1

Truth Tables

13.1.1

Truth Tables

You can make the following settings here:

●

Truth Tables 1-6 (3I - 1O)

●

Truth Tables 10, 11 (3I - 1O)

●

Truth Tables 7-8 (2I - 1O)

●

Truth Tables 9 (5I - 2O).

13.1.2

Table 1 (3I - 1O)

13.1.2.1

Table 1 (3I - 1O)

The Truth Table for 3I/1O consists of:

●

3 plugs

●

1 logic component

●

1 socket (Truth Table Output).

You can choose from the 8 possible input conditions the one with which to generate an

output signal.
8 Truth Tables (1 to 6, 10, 11) are available for SIMOCODE pro V PN Basic Unit.

13.1.2.2

Input Table 1 (3I - 1O)

Activate the Truth Table with any signal (any sockets, e.g. device inputs, control bits from

PROFINET, etc.

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды