Siemens SIMATIC TDC Скачать руководство пользователя страница 152

Страница: 152 / 228

Communication modules

6.4 CP52IO GDM interface module

SIMATIC TDC hardware

152

System Manual, 08/2017, A5E01114865-AL

6.4.3

Status and fault displays

Status displays for CP52IO

Table 6- 17 Status and fault displays of the CP52IO GDM interface module

LED display

State

H1
H3
H5
H7

Off

No data transfer to the CP52A0 GDM access module

Glowing

/lit Data transfer to the CP52A0 GDM access module

Flashing with

0.5 Hz

The CP52IO module is inserted in the wrong slot

H2
H4
H6
H8

Off

Missing or incorrect data transfer from the CP52A0GDM access module

Glowing

/lit Error-free data transfer from the CP52A0 GDM access module

Flashing with

0.5 Hz

The CP52IO module is inserted in the wrong slot

The brightness of the LED indicates the density of periodic data traffic.

6.4.4

Application notes and immunity to interference

The CP52IO GDM access modules in the racks are connected to the CP52A0 GDM

interface module via fiber-optic cables (FOC). Up to four racks can be connected to each

CP52IO.

●

The CP52IO modules must be inserted between slots 2 and 12.

●

Free slots between the individual modules are allowed.

●

The rack may be equipped with a maximum of 11 CP52IO interface modules.

●

Modules may not be inserted in slots 13 - 21.

●

You may insert the fiber-optic cables into the FOC interfaces of CP52IO to suit your

application.

●

It is not necessary to occupy all FOC interfaces of CP52IO.

●

Memory access rates do not depend on which CP52IO the fiber-optic cable is connected,

●

as all FOC interfaces are assigned the same priority.

●

Interference-proof operation is only possible if the CP52IO is firmly attached to the rack.

Insert the module and then bolt it onto the rack accordingly (two screw heads, see

"Control and display elements (Page 150)").

●

The module may not be inserted or removed while the rack is on live voltage.

●

Removal and insertion of the fiber-optic cables is not permitted during operation.

Note
See also:

•

For more information on fan operation, refer to chapter "Rack (Page 39)".

•

For more information on EMC and environmental conditions, refer to chapter "General

technical specifications (Page 37)".

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание SIMATIC TDC





































































































































































































































Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды

Siemens SIMATIC TDC, Системное руководство

Результаты поиска

Содержание SIMATIC TDC

Отзывы:

Похожие инструкции для SIMATIC TDC

Бренды по названию

Популярные бренды