Siemens SIMATIC S7-400 CP 440 Скачать руководство пользователя

Страница: 22 / 156

Basic Principles of Serial Data Transmission

2.1 Serial Transmission of a Character

Point-to-point connection CP 440 Installation and Parameter Assignment

Manual, 09/2007, A5E00057742-03

Bidirectional Data Traffic - Operating Modes

The CP 440 has two operating modes for bidirectional data traffic:
●

Half-duplex operation (3964(R) procedure, ASCII driver)
Data is exchanged between the communication partners but only in one direction at a

time. In half-duplex operation, therefore, at any one time data is being either sent or

received. The exception to this may be individual control characters for data flow control

(e.g. XON/XOFF), which can also be sent during a receive operation or received during a

send operation.

●

Full-duplex operation (ASCII driver)
Data is exchanged between two or more communication partners in both directions

simultaneously. In full-duplex operation, therefore, data can be sent and received at the

same time. Every communication partner must be able to operate a send and a receive

facility simultaneously.

Only half-duplex mode can be used with an RS 485 (2-wire) setting.

Asynchronous Data Transmission

With the communication processor, serial transmission occurs asynchronously. The so-

called time base synchronism (a fixed timing code used in the transmission of a fixed

character string) is only upheld during transmission of a character. Each character to be sent

is preceded by a synchronization impulse, or start bit. The length of the start-bit transmission

determines the clock pulse. The end of the character transmission is signaled by the stop bit.

Declarations

As well as the start and stop bits, further declarations must be made between the sending

and receiving partners before serial transmission can take place. These include:
●

Transmission speed (baud rate)

●

Character and acknowledgment delay times

●

Parity

●

Number of data bits and

●

Number of stop bits

www.jisupdfeditor.com/

长沙工控帮教育科技有限公司

www.gkbpx.com

Содержание SIMATIC S7-400 CP 440





























































































































































Результаты поиска

Содержание SIMATIC S7-400 CP 440

Отзывы:

Похожие инструкции для SIMATIC S7-400 CP 440

Бренды по названию

Популярные бренды

Siemens SIMATIC S7-400 CP 440, Установка и настройка параметров

Результаты поиска

Содержание SIMATIC S7-400 CP 440

Отзывы:

Похожие инструкции для SIMATIC S7-400 CP 440

Бренды по названию

Популярные бренды