Siemens SIMATIC S7-1200 CP 1243-8 IRC страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 230

background image

Application and functions

1.8 Requirements for operation

CP 1243-8 IRC
Operating Instructions, 02/2018, C79000-G8976-C385-03

23

The send buffer has a maximum size of 16000 frames. The size of the frame memory is

divided equally among all configured communications partners. It can be set in STEP 7

Basic, refer to the section Communication with the CPU (Page 95).
You will find details of how the send buffer works (storing and sending events) as well as the

options for transferring data in the section Process image, type of transmission, event

classes (Page 144).

Messages: E-mail / SMS

Up to 10 messages can be configured in STEP 7 and sent as e-mails or SMS messages.

●

Maximum number of characters that can be transferred per SMS message: 160 ASCII

characters including any value sent at the same time

●

Maximum number of characters that can be transferred per e-mail: 256 ASCII characters

including any value sent at the same time

IPsec tunnel (VPN)

Up to 8 IPsec terminals can be established for secure communication with other security

modules.

Firewall rules

The maximum number of firewall rules in advanced firewall mode is limited to 256.
The firewall rules are divided up as follows:

●

Maximum 226 rules with individual addresses

●

Maximum 30 rules with address ranges or network addresses

(e.g. 140.90.120.1 - 140.90.120.20 or 140.90.120.0/16)

●

Maximum 128 rules with limitation of the transmission speed ("Bandwidth limitation")

1.8

Requirements for operation

Hardware

Apart from the CP, in the remote S7-1200, the following hardware is also required:

●

A CPU with firmware version as of V4.1

●

For communication via WAN networks (dedicated line, dial-up / GSM / wireless network):

A TS module
You will find the TS modules in the telecontrol accessories program, refer to the appendix

TS modules (Page 193).
A TS basic device (TS Adapter) is not required.

«
...
21
22
23
24
25
...
»

Содержание SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Бренд: F5 Страницы: 2

Бренд: F5 Страницы: 90

Бренд: F5 Страницы: 47

Бренд: T&D Страницы: 122

Бренд: TC-Helicon Страницы: 2

Бренд: TANDBERG Страницы: 3

Бренд: A2B Electronics Страницы: 24

Бренд: ZALMAN Страницы: 6

iTRON B 70.2040

Бренд: JUMO Страницы: 41

Бренд: AXIOMTEK Страницы: 58

Бренд: Microchip Technology Страницы: 9

Бренд: PairGain Страницы: 80

Бренд: RR-Concepts Страницы: 12

Бренд: Omron Страницы: 14

Бренд: Net Optics Страницы: 2

Бренд: Hologic Страницы: 256

Бренд: EVGA Страницы: 3

Soundweb 9088ii DSP System

Бренд: BSS Audio Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды