manualshive.com logo in svg

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Руководство по эксплуатации

"Siemens SIMATIC S7-1200 CP 1243-8 IRC" - это компактный коммуникационный модуль, предназначенный для промышленного оборудования. Для более детального ознакомления с функционалом устройства, вы можете скачать бесплатное руководство по эксплуатации на нашем сайте. (website) - ваш источник операционных инструкций и руководств по эксплуатации.

Поделиться
Скачать
background image

Accessories 

 

C.4 Connecting cables 

 

CP 1243-8 IRC 

210

 

Operating Instructions, 02/2018, C79000-G8976-C385-03 

C.4

 

Connecting cables 

C.4.1

 

Connecting cables for connecting the CP to Ethernet 

Connecting cables for connecting to Ethernet 

For the Ethernet attachment of the TIM 4RIE DNP3, you can use a standard Ethernet 

connecting cable (for example IE TP Cord) from the SIMATIC NET product range (catalog 

IK PI). 
The cable must be suitable for the 10Base-TX or 100Base-TX Ethernet specification. 
If the CP is connected to a switch or router, it is advisable to use fully shielded straight-

through patch cables with RJ-45 connectors at both ends and 1:1 pin assignment. The cable 

must be suitable for the 10Base-TX or 100Base-TX specification. 
You can also use a crossover patch cable with RJ-45 connectors at both ends and the 

following pin assignment: 

 

Figure C-6  Pinout of a crossover Ethernet RJ-45 cable 

C.4.2

 

Connecting cables for connecting the modem of the TS Module RS232 

Connecting cables for connecting the TS Module RS232 to a modem 

A modem or other transmission device can be connected to the 9-pin D-sub connector of the 

of the RS-232 interface of the TS module. 

Содержание SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Бренд: Panasonic Страницы: 4
Intel Optane M Series Installation And User Manual preview
Optane M Series
Бренд: Intel Страницы: 59
DAD DPX2060 User Manual preview
DPX2060
Бренд: DAD Страницы: 32
NEC P401-TMX4D User Manual preview
P401-TMX4D
Бренд: NEC Страницы: 2
Dazzle Hollywood DV-Bridge User Manual preview
Hollywood DV-Bridge
Бренд: Dazzle Страницы: 63
HARTING HAIIC MICA Hardware Development Manual preview
HAIIC MICA
Бренд: HARTING Страницы: 13
UfiSpace S9600-64X Hardware Installation Manual preview
S9600-64X
Бренд: UfiSpace Страницы: 35
Point of View SmartTV 210 User Manual preview
SmartTV 210
Бренд: Point of View Страницы: 13
Dahua D-NVR4108HS-4KS2/L Quick Start Manual preview
D-NVR4108HS-4KS2/L
Бренд: Dahua Страницы: 33
Arbor Technology Em104P-i2904 Quick Installation Manual preview
Em104P-i2904
Бренд: Arbor Technology Страницы: 8
ZALMAN CNPS7000C Series User Manual preview
CNPS7000C Series
Бренд: ZALMAN Страницы: 8
Eurotech Zypad WL15 Series Quick Start preview
Zypad WL15 Series
Бренд: Eurotech Страницы: 2
Isee IGEPv2 BOARD Hardware Reference Manual preview
IGEPv2 BOARD
Бренд: Isee Страницы: 68
McIntosh MX160 Owner'S Manual preview
MX160
Бренд: McIntosh Страницы: 44
Aleratec 260206 Quick Start Manual preview
260206
Бренд: Aleratec Страницы: 16
Avigilon NVR5-STD-10GBE Installation Manual preview
NVR5-STD-10GBE
Бренд: Avigilon Страницы: 12
Galileo Quark SoC X1000 Getting Started Manual preview
Quark SoC X1000
Бренд: Galileo Страницы: 20
Apposite Technologies Linktropy MINI-G User Manual preview
Linktropy MINI-G
Бренд: Apposite Technologies Страницы: 57

Бренды по названию

Популярные бренды

Загрузить еще бренды