Siemens SIMATIC RF1000 Series Скачать руководство пользователя страница 73

Страница: 73 / 77

Appendix

A.1 Certificates & approvals

SIMATIC RF1000
Operating Instructions, 02/2020, C79000-G8976-C432-07

Marking

Description

Thailand

Marking requirements (only SIMATIC RF1060R/RF1070R):
Following statement may be displayed on packaging or additional

page or on user's manual. For Sdoc, it is optional to display this

wording.
“

เครื่องโทรคมนาคมและอุปกรณ์นี้มีความสอดคล้องตามมาตรฐานหรือข้อกําห

นดทางเทคนิคของ

กสทช

.”

This telecommunication equipment conforms to the technical stand-

ards or requirements of NBTC.

A.1.2

Using the reader in hazardous areas

NOTICE
Device-specific validity of the directive
Please note that the directive and marking described in this section are valid only for the

SIMATIC RF1000 readers with the following product versions:

•

SIMATIC RF1060R as of product version "AS: B"

•

SIMATIC RF1070R as of product version "AS: C"

The directive/marking is not valid for other device variants or older product versions.

NOTICE
Validity only when the devices are marked
The corresponding approval only exists for devices to which the Ex mark is applied.

TÜV NORD CERT GmbH, appointed center no. 0044 as per Article 18 of the directive of the

European Council of 26 February 2014 (2014/34/EU), has confirmed compliance with the

essential health and safety requirements relating to the design and construction of

equipment and protective systems intended for use in hazardous areas as per Annex II of

the directive.

The essential health and safety requirements are satisfied in accordance with the standards:

●

EN IEC 60079-0: Equipment - General requirements

●

EN 60079-7: Equipment protection by increased safety "e"

●

EN 60079-31: Equipment dust ignition protection by enclosure "t"

This allows the reader to be used in hazardous areas for gases, for the device category 3 G

and gas group IIC, or alternatively in hazardous areas for dusts, for the device category 3 D

and group IIIC.

Содержание SIMATIC RF1000 Series














































































Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды

Siemens SIMATIC RF1000 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды