Siemens SIMATIC RF1000 Series Скачать руководство пользователя страница 15

Страница: 15 / 77

SIMATIC RF1000
Operating Instructions, 02/2020, C79000-G8976-C432-07

Connecting

WARNING

Explosion hazard
Note that installation must not be performed and the connecting cable must not be inserted

or removed within the hazardous area.

NOTICE
Permissible power supply
The device can only be connected to a 5 V DC power supply which satisfies the

requirements of safe extra low voltage (SELV).

Required tools

When using the RS232 interface, you need to attach the corresponding cable to the reader

first. You require the following tools for this purpose:

●

Torx screwdriver (T10)

●

Additional tools depending on the connector used

Accessories required

You need the following accessories:

●

For communication via the USB interface,
the pre-assembled connecting cable included in the scope of delivery

●

For communication via the RS232 interface with a SIMATIC Ident communication

module,
the connecting cable (6GT2891-4UH20)

●

For communication via the RS232 interface with any serial module,
the connecting cable with open ends (6GT2891-2UH30)

Содержание SIMATIC RF1000 Series














































































Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды

Siemens SIMATIC RF1000 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды