Siemens SIMATIC PCS 7 Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 434

background image

Plant changes in RUN - CiR

11.9 Reconfigure existing modules in ET200M / ET200iSP stations

CPU 410 Process Automation/CPU 410 SMART

186

System Manual, 05/2017, A5E31622160-AC

11.9.2

Module Response During a Reconfiguration

Principle

During reconfiguration the input modules can respond in one of the three following ways:

●

Channels not affected will continue to return the actual process value.

●

Channels not affected will return the process value which was valid prior to the

reconfiguration.

●

All channels will return the value "0" (applies to digital modules and FMs) or W#16#7FFF

(applies to analog modules).

Please refer to the technical data of the specific modules for information on their response.
Output modules respond as follows during reconfiguration:
The respective channels output the initial value which was valid before the parameter

assignment.

11.9.3

CPU response during reconfiguration

Re-configuration sequence

Once you have made the parameter changes in HW Config and have downloaded them to

the CPU in RUN mode, the CPU runs the tests described in "Behavior of the CPU after

download of the configuration in RUN". The input and output values have the status "OK"

after successful re-configuration.
You may only access those values in the process image that belong to the process image

partition of the OB currently being processed.
The DP master marks the modules as available in the module status data if data record

transfer was successful and as unavailable if data record transfer was not successful. In the

latter case, access to the module triggers an I/O access error (in the event of input process

image updates, transmission of the output process image to the module or direct access to

the module. Depending on the type of access, OB 85 or OB 122 is started).
The input or output data of the modules behaves in the same way as after a remove module

interrupt, which means it may not yet be correct (because the module may not yet have

evaluated its data records). However, the restriction that data record SFCs for the modules

can no longer be active no longer applies.

Note
If the re-configuration of a module involves disabling the diagnostic interrupt, for example,

the module may still subsequently send an interrupt that it has already prepared.

«
...
184
185
186
187
188
...
»

Содержание SIMATIC PCS 7



















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC PCS 7

FPBA-01 PROFIBUS DP

Бренд: ABB Страницы: 2

ControlMaster CM15

Бренд: ABB Страницы: 4

Бренд: UE Страницы: 4

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: ZETRON Страницы: 3

Бренд: C.Nord Страницы: 100

CoreBuilder 9000

Бренд: 3Com Страницы: 78

REMOTE ACCESS SYSTEM 1500

Бренд: 3Com Страницы: 62

Бренд: H-P Products Страницы: 12

Бренд: Kathrein Страницы: 16

Бренд: Watts Страницы: 12

Бренд: Lancom Страницы: 8

Бренд: Keba Страницы: 16

Бренд: KEB Страницы: 16

Бренд: Vaillant Страницы: 12

Бренд: Saluki Страницы: 13

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды