Siemens SIMATIC PCS 7 FOUNDATION Fieldbus Скачать руководство пользователя страница 11

Страница: 11 / 72

Basics of the FOUNDATION Fieldbus

FOUNDATION Fieldbus (FF) and PROFIBUS PA operate according to IEC 61158-2. The

communication on the fieldbus and the voltage supply of the bus nodes are combined in one

shielded two-wire cable. Up to 32 bus nodes are possible on one FF segment (bus link +

maximum of 31 field devices). Data packets are modulated and transmitted on the supply

voltage for the fieldbus nodes. The transfer rate is 31.25 Kbps.

The most important distinctions between PROFIBUS PA and FOUNDATION Fieldbus

Licensing
● You need the "PDM Foundation Fieldbus" license key to work with SIMATIC PDM.

Operating mode
● PROFIBUS PA devices are operated in master/slave mode.
● FF devices are operated in publisher/subscriber mode.

Connection to PROFIBUS DP
● PROFIBUS PA devices are connected to up to five FDC 157 DP/PA couplers via DP/PA-

Link (redundancy with 2 fieldbus couplers possible).

● FF devices are connected to the automation system via a bus link. The following bus links

are approved for PCS 7:
– FF Link

Configuration with an IM 153-2 FFinterface module and FDC 157 fieldbus coupler

(redundancy with 2 fieldbus couplers possible)

– Compact FF Link

Configuration with Compact FF Link (redundancy with 2 Compact FF Link possible)

Communication with the automation system
● PROFIBUS PA devices only communicate via the automation system. An exception to this

rule is the direct access to a PA device.

● FF devices can communicate on the FF segment without involvement of the automation

system. The name of this function is "Control in the field" (CiF). CiF enables technological

function between FF devices.

Terms used for FOUNDATION Fieldbus (FF)

Publisher and Subscriber
In the time period during which an FF device sends data to the FF, it is referred to as the

Publisher.

FOUNDATION Fieldbus

Commissioning Manual, 02/2015, A5E32711026-AC

Содержание SIMATIC PCS 7 FOUNDATION Fieldbus









































































Результаты поиска

Содержание SIMATIC PCS 7 FOUNDATION Fieldbus

Отзывы:

Siemens SIMATIC PCS 7 FOUNDATION Fieldbus, Руководство по вводу в эксплуатацию, Страница: 11 / 72

Результаты поиска

Содержание SIMATIC PCS 7 FOUNDATION Fieldbus

Отзывы: