Siemens SIMATIC NET страница 95 Скачать руководство пользователя | Manualshive

Страница: 95 / 464

background image

Functions specific to SCALANCE

4.2 Signal recorder

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

95

Result

The status of the signal recorder and the recording are displayed.

●

If the recording has started, the configured interval and the current number of recorded

measured values are displayed.

●

If the recording has stopped, the configured interval and the number of recorded

measured values are displayed.

4.2.2

wlan signal-recorder start (client)

Description

With this command, you configure and start recording with the signal recorder. The recorded

measured values are saved every 10 minutes and logged in files. On completion of the

recording, the files can be downloaded as a zip file using http or tftp.
The automatic saving contains only the last fully elapsed 10 minutes. The remaining minutes

are discarded.
If the signal recorder is ended manually or if the procedure was ended automatically, the file

contains all the values since the start of the recording.
If a recording is interrupted before 10 minutes have elapsed (e.g. due to a restart or power

down), no signal recorder file is saved.

Note
This command is only available in the client mode.

Requirement

●

The WLAN interface is enabled.

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

or

cli#

Syntax

Call up the command with the following parameters:

wlan signal-recorder <wlan 0/X> <ms (1 - 60000)> <sample_number(1 - 20000)> start

«
...
93
94
95
96
97
...
»

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC NET

Бренд: Barrett Страницы: 4

Бренд: Adeunis RF Страницы: 7

Бренд: Yaesu Страницы: 16

BELGIAN SHEPHERD

Бренд: Parsec Technologies Страницы: 4

Бренд: Poynting Страницы: 12

Бренд: Hughes Network Systems Страницы: 27

Бренд: KNS Страницы: 75

Бренд: Buddipole Страницы: 3

Бренд: ETS-Lindgren Страницы: 18

Бренд: ETS-Lindgren Страницы: 20

Бренд: ETS-Lindgren Страницы: 27

Бренд: Hughes Страницы: 80

Бренд: CommScope Страницы: 24

Бренд: Winegard Страницы: 8

Бренд: YIC Technologies Страницы: 7

Бренд: IKUSI Страницы: 2

Бренд: Satfi Страницы: 33

Бренд: Steren Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды