Siemens SIMATIC NET Скачать руководство пользователя страница 72

Страница: 72 / 464

Configuration

3.2 Load and Save

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

Configuration Manual, 10/2015, C79000-G8976-C351-05

3.2.3

load tftp

Description

With this command, you load the files from a TFTP server.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call up the command with the following parameters:

load tftp {ipv4 <ucast_addr> | fqdn-name <FQDN>} [port <tcp port (1-65535)>] file

<filename> filetype <filetype>

The parameters have the following meaning:

Parameter

Description

Range of values / note

ipv4

Keyword for an IPv4 address

ucast_addr

IPv4 unicast address of the TFTP

server

Enter a valid unicast IPv4 ad-

dress.

fqdn-name

Keyword for a domain name

FQDN

Domain name (Fully Qualified Domain

Name) of the TFTP server

Maximum of 100 characters

port

Keyword for the port of the server via

which the TFTP connection runs

tcp port

Number of the port

1 … 65535

file

Keyword for a file name to be assigned -

filename

Name of the file

Maximum of 100 characters

filetype

Keyword for the file type to be loaded

filetype

Name of the file type

Maximum of 100 characters

For information on identifiers of addresses and interfaces, refer to the section "Auto-

Hotspot".
For information on the file types , refer to this list.

Result

The file is loaded on the device from the TFTP server.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Siemens SIMATIC NET, Руководство по настройке, Страница: 72 / 464

Результаты поиска

Содержание SIMATIC NET

Отзывы: