manualshive.com logo in svg

Siemens SIMATIC NET, Руководство по настройке, Страница: 53 / 464

Поделиться
Скачать
Siemens SIMATIC NET Скачать руководство пользователя страница 53

 

Configuration 

 

3.1 System 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

53

 

Result  

EtherNet/IP is enabled or disabled after the next restart. 

Further notes 

You can display the current EtherNet/IP configuration with the 

show ethernetip

 command.  

3.1.9.5

 

interface 

Description 

With this command, you change to the Interface Configuration mode.  
There you can edit the settings for one interface. You select the interface with the 

parameters of this command. If you specify a logical interface that does not exist, it will be 

created. The name of the selected interface is displayed in the command prompt. 

Requirement 

You are in the Global Configuration mode. 
The command prompt is as follows: 

cli(config)#

 

Syntax 

Call up the command with the following parameters: 

interface{vlan<vlan-id(1-4094)> 

          <interface-type><interface-id>}

 

The parameters have the following meaning: 

 

Parameter 

Description 

Range of values / note 

vlan

 

Keyword for a VLAN connection 

- 

vlan-id

 

Number of the addressed VLAN 

1 … 4094 

interface-type

 

Type or speed of the interface 

Enter a valid interface. 

interface-id

 

Module no. and port no. of the interface 

Result  

You are in the Interface Configuration mode. 
The command prompt is as follows: 

cli(config-if-$$$)#

 

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов