Siemens SIMATIC NET страница 382 Скачать руководство пользователя

Страница: 382 / 464

Security and authentication

10.1 User rights management

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

382

Configuration Manual, 10/2015, C79000-G8976-C351-05

Result

The password is changed.

Note
Changing the password in Trial mode
Even if you change the password in Trial mode, this change is saved immediately.

Further notes

You create a user with the

user-account

command.

You delete a user with the

no user-account

command.

You show the created users with the

show user-accounts

command.

10.1.2

whoami

Description

This command shows the user name of the logged in user.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call the command without parameters:

whoami

Result

The user name of the logged in user is displayed.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды