Siemens SIMATIC NET страница 340 Скачать руководство пользователя

Страница: 340 / 464

Network protocols

7.4 SNMP

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

340

Configuration Manual, 10/2015, C79000-G8976-C351-05

Syntax

Call up the command with the following parameters:

snmp group <GroupName> user <UserName>security-model{v1|v2c|v3}

[{volatile|nonvolatile}]

The parameters have the following meaning:

Parameter

Description

Range of values / note

GroupName

Name of the group

max. 32 characters

user

Keyword for the user name

UserName

Name of the user

max. 32 characters

security-model

specifies which security settings will be

used

•

v2c

•

Storage type

specifies whether the settings remain

following a restart

•

volatile

(volatile):

The settings are lost after a

restart

•

nonvolatile

(non-volatile):

The settings are retained after

a restart

If optional parameters are not specified when configuring a group, the default values apply.

Result

The details of the group are configured.

Further notes

You delete the details of an SNMP group with the

no snmp group

command.

You display the created SNMP groups with the

show snmp group

command.

You display the created SNMP user with the

show snmp user

command.

7.4.2.11

no snmp group

Description

With this command, you delete the details of an SNMP group.

Requirement

You are in the Global configuration mode.
The command prompt is as follows:

cli(config)#

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды