Siemens SIMATIC NET страница 335 Скачать руководство пользователя

Страница: 335 / 464

Network protocols

7.4 SNMP

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

335

The parameters have the following meaning:

Parameter

Description

Range of values / note

GroupName

Name of the group to which access is

deleted

max. 32 characters

Version

Selects the version of the protocol

used

•

v2c

•

Authentication

Selects the authentication method:

•

auth

•

noauth

•

priv

Result

The access to an SNMP group is deleted.

Further notes

You configure the setting with the

snmp access

command.

You display the configured SNMP groups with the

show snmp group

command.

You display the access configurations for SNMP groups with the

show snmp group access

command.
You display the configured SNMP tree views with the

show snmp viewtree

command.

7.4.2.6

snmp community index

Description

With this command, you configure the details of an SNMP community.

Requirement

You are in the Global configuration mode.
The command prompt is as follows:

cli(config)#

Syntax

Call up the command with the following parameters:

snmp community index <CommunityIndex> name <CommunityName>

security <SecurityName> [context <Name>][{volatile|nonvolatile}]

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды