Siemens SIMATIC NET страница 327 Скачать руководство пользователя

Страница: 327 / 464

Network protocols

7.4 SNMP

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

327

7.4.1.5

show snmp group

Description

This command shows the configured SNMP groups.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call the command without parameters:

show snmp group

Result

The configured SNMP groups are displayed.

7.4.1.6

show snmp group access

Description

This command shows the rights of the configured SNMP groups.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call the command without parameters:

show snmp group access

Result

The rights of the configured SNMP groups are displayed.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды