Siemens SIMATIC NET страница 321 Скачать руководство пользователя

Страница: 321 / 464

Network protocols

7.3 DHCP server

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

321

7.3.3.9

set-interface

Note
The command is only available with the following device:

•

SCALANCE W722-1 RJ-45 (MLFB 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-0AB0

(US version))

•

SCALANCE W761-1 RJ45 in access point mode (article number): 6GK5761-1FC00-0AA0

and 6GK5761-1FC00-0AB0 (US version))

Description

With this command, you specify the interface via which the IPv4 addresses are dynamically

assigned.
The requirement for the assignment is that the IPv4 address of the interface is located within

the IPv4 address band. If this is not the case, the interface does not assign any IPv4

addresses.

Requirement

You are in the DHCPPOOL configuration mode.
The command prompt is as follows:

cli(config-dhcp-pool-<ID>)#

Syntax

Call up the command with the following parameters:

set-interface {vlan <vlan-id (1-4094)> | <interface-type> <interface-id> }

The parameters have the following meaning:

Parameter

Description

Range of values / note

vlan

Keyword for a VLAN connection.

vlan-id

Number of the

addressed VLAN

1 ... 4094

interface-type

Type or speed of the interface

Enter a valid interface

interface-id

Module no. and port no. of the interface

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Result

The interface is assigned. Before the IPv4 address band can be used, it still needs to be

activated.

Further notes

You display the setting with the

show ip dhcp-server pools

command.

You enable the IPv4 address band with the

pool-enable

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды