Siemens SIMATIC NET Скачать руководство пользователя страница 134

Страница: 134 / 464

Network structures

6.1 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

134

Configuration Manual, 10/2015, C79000-G8976-C351-05

6.1.1.4

show wlan ap (access point)

Description

The command displays the configuration parameters of the access point.

Note
This command is available only in access point mode.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call up the command with the following parameters:

show wlan ap <wlan 0/X>

The parameter has the following meaning:

Parameter

Description

Range of values / note

wlan 0/X

WLAN interface

Enter a valid interface.

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Result

The following settings of the access point are displayed:

●

Channel

●

Alternative channel

●

HT channel width

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Siemens SIMATIC NET, Руководство по настройке, Страница: 134 / 464

Результаты поиска

Содержание SIMATIC NET

Отзывы: