Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 94

Страница: 94 / 294

Installation guide

3.2 Installing the TIM 4R-IE in an S7-300

SINAUT ST7 station control system

System Manual, 09/2016, C79000-G8976-C178-10

3.2

Installing the TIM 4R-IE in an S7-300

Introduction

The TIM 4R-IE can be used in an S7-300 as a communications processor (CP). All S7-300

standard and compact CPUs can be combined with the TIM 4R-IE. There are, however,

constraints that must be taken into account relating to the way in which data exchange

between the TIM and the CPU in the rack is handled (the SINAUT program). For the

TIM 4R-IE, there are two options:
1.

TD7onTIM

This SINAUT TD7 program runs on the TIM.

All standard and compact CPUs can be used without restriction.

TD7onCPU

This SINAUT TD7 program runs on the CPU and is created for the CPU with the blocks

from the SINAUT TD7 library.

In this case, only CPUs with a work memory adequate to accommodate the SINAUT

program can be used. The size of the program depends on the amount of data to be

transmitted. At least 20 Kbytes are required.
TD7onCPU can be used for several CPU types if the following software packages are

used:
–

"SINAUT TD7 library for the CPU" as of V2.2

–

"TIM firmware" as of V1.0

The following CPU lists also include older CPU types that can no longer be ordered as new

devices but that nevertheless may still be in use in the field.

Standard CPU type

As of article number

CPU 312

6ES7 312-1AD10-0AB0

6ES7 312-1AE13-0AB0

6ES7 312-1AE14-0AB0

CPU 312 IFM

6ES7 312-5AC00-0AB0

6ES7 312-5AC02-0AB0

CPU 313

6ES7 313-1AD00-0AB0

6ES7 313-1AD01-0AB0

6ES7 313-1AD02-0AB0

6ES7 313-1AD03-0AB0

CPU 314

6ES7 314-1AE02-0AB0

6ES7 314-1AE03-0AB0

6ES7 314-1AE04-0AB0

6ES7 314-1AF10-0AB0

6ES7 314-1AF11-0AB0

6ES7 314-1AG13-0AB0

6ES7 314-1AG14-0AB0

CPU 314 IFM

6ES7 314-5AE02-0AB0

6ES7 314-5AE03-0AB0

6ES7 314-5AE10-0AB0

CPU 315

6ES7 315-1AF01-0AB0

6ES7 315-1AF02-0AB0

6ES7 315-1AF03-0AB0

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Бренды по названию

Популярные бренды