Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 141

Страница: 141 / 294

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

141

Installation and commissioning of the modems and

routers

5.1

Overview

Introduction

The following modem variants are available in the SINAUT ST7 range.

MD720-3 GSM wireless modem

for data transmission over the GSM mobile wireless network by establishing a

dial-up connection (CSD, Circuit Switched Data)

or for IP.based data transmission with the MSC protocol (GPRS)

max. 9,600 bps

MD741-1 GPRS router

for data transmission using the (E)GPRS service (General Packet Radio Ser-

vice) of a mobile wireless provider,

secure connection with integrated VPN router and firewall,

max. 54 Kbps

MD2

Dedicated line modem

for multipoint connection, can be tapped.

Can also be used as a repeater,

max 19,200 bps

MD3

Modem for the analog telephone network,

max. 33,600 bps.

Can also be used a dedicated line modem for a point to-point connection,

max. 33,600 bps in voice band

MD4

Modem for the digital ISDN network

max. 64,000 bps

5.2

Important notes on using the device

Safety notices on the use of the device

The following safety notices must be adhered to when setting up and operating the device

and during all work relating to it such as installation, connecting up, replacing devices or

opening the device.

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды