manualshive.com logo in svg

Siemens SIMATIC NET SCALANCE XCM-300, Руководство по эксплуатации продукта

Поделиться
Скачать
Siemens SIMATIC NET SCALANCE XCM-300 Скачать руководство пользователя страница 53

Autonegotiation

Autonegotiation means the automatic detection/negotiation of the transmission rate and the 
operating mode of ports at the opposite end. This makes it possible to configure different devices 
automatically.

Two components connected to a link segment can exchange information about the transfer and 
can adapt their settings to each other. The mode with the highest possible speed is set.

Note
• If a port is set permanently to full duplex, the connected partner port must also be set to full

duplex.

• If a port operating in the "Auto negotiation" mode is connected to a partner port that is not

operating in the"Auto negotiation" mode, the partner port setting must be fixed at 100 Mbps
or 10 Mbps half duplex mode.

• If you disable the "Auto negotiation" function, the "MDI/MDI-X autocrossover" function is also

turned off. Then use a crossover cable.

6.6

Signaling contact

The signaling contact is an event-driven or manually controlled failsafe alarm relay. Individual 
alarms can be configured to trigger the relay when the associated event occurs. The relay can 
also be fixed in an open or closed state.

Manually controlling the relay may be useful to:

• Verify the failsafe relay is properly connected following the installation of the device

• Verify the open/close state is caused by the device itself or some other hardware

• Keep the relay in an open/close state while troubleshooting a network issue

Information on the signaling contact

• The signaling contact is a floating switch that signals error statuses by opening the contact.

The signaling contact must be operated within the range of the operating voltage.
If an error/fault occurs, the signaling contact opens. In normal operation, the signaling
contact is closed.

• The signaling contact is connected using a 2-pin plug-in terminal block (spring-loaded

terminal). The terminal block is included in the scope of delivery of the device and can be
ordered as a spare part, see section "Spare parts (Page 21)".

• Note the wiring rules (Page 48).

• The signaling contact can be controlled manually using the CLI commands. Information on

this can be found in the Configuration manuals (Page 7).

Connecting up

6.6 Signaling contact

SCALANCE XCM-300

Product

 Manual, 04/2022, C79000-G8976-C585-01

53

Содержание SIMATIC NET SCALANCE XCM-300



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды