Siemens SIMATIC NET SCALANCE XB-200 Series Скачать руководство пользователя страница 27

Страница: 27 / 78

Installation

5.1

Safety notices for installation

Safety notices

When installing the device, keep to the safety notices listed below.

WARNING

If a device is operated in an ambient temperature of more than 50 °C, the temperature of the

device housing may be higher than 70 °C. The device must therefore be installed so that it is

only accessible to service personnel or users that are aware of the reason for restricted access

and the required safety measures at an ambient temperature higher than 50 °C.

WARNING

If the device is installed in a cabinet, the inner temperature of the cabinet corresponds to the

ambient temperature of the device.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD
Replacing components may impair suitability for Class 1, Division 2 or Zone 2.

WARNING

The device may only be operated in an environment with pollution degree 1 or 2 (see

IEC 60664-1).

WARNING

When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone

2, the device must be installed in a cabinet or a suitable enclosure.

SCALANCE XB-200

Operating Instructions, 03/2020, C79000-G8976-C359-09

Содержание SIMATIC NET SCALANCE XB-200 Series















































































Результаты поиска

Содержание SIMATIC NET SCALANCE XB-200 Series

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE XB-200 Series

Бренды по названию

Популярные бренды

Siemens SIMATIC NET SCALANCE XB-200 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET SCALANCE XB-200 Series

Отзывы:

Похожие инструкции для SIMATIC NET SCALANCE XB-200 Series

Бренды по названию

Популярные бренды