background image

 

SCALANCE W788-x / W748-1 
Operating Instructions, 03/2022, A5E03678333-17 

67

 

Technical specifications

 

9.1

 

SCALANCE W7x8-1 

The following technical specifications apply to the following devices: 

 

SCALANCE W788-1 RJ45 

 

SCALANCE W788-1 M12 

 

SCALANCE W748-1 RJ45 

 

SCALANCE W748-1 M12 

 

Note 

Bridging a power outage is possible only with an input voltage of 24 VDC (-15% to 

+20%). 

 

 

Note 

You will find detailed information on the transmit power and receiver sensitivity in the 

document "Leistungsdaten 802.11abgn PCIe Minicard / Characteristics 802.11abgn PCIe 

Minicard" (REF_W700-RadioInterface.pdf). 

 

Technical specifications 
Data transfer

 

Ethernet transfer rate 

 

10 / 100 / 1000 Mbps 

Wireless transmission rate 

 

1 ... 450 Mbps 

Wireless standards supported   

IEEE 802.11a 

IEEE 802.11b 

IEEE 802.11g 

IEEE 802.11h 

IEEE 802.11n 

Power supply standards 

supported 

Type 

IEEE 802.3at type 1 (802.3af) 
IEEE 802.3at type 2 (Power over 

Ethernet) 

Class 

Class 3 *

)

 

Attachment to Industrial Ethernet

 

RJ-45 variants 

Quantity 

Design 

RJ-45 jack 

Properties 

Half duplex/full duplex, autocrossover, 

autonegotiation, autosensing, PoE, 

floating 

M12 variants 

Quantity 

Design 

M12 socket 

Properties 

Half duplex/full duplex, autocrossover, 

autonegotiation, autosensing, PoE, 

floating 

Содержание SIMATIC NET SCALANCE W748-1















































































Отзывы: