Siemens SIMATIC NET S7-1200 Скачать руководство пользователя страница 33

Страница: 33 / 98

CP 1242-7
Operating Instructions, 09/2011, C79000-G8976-C247-02

Notes on operation

CAUTION

Minimum clearance to the device
The device may only be operated when the distance between the device (or antenna) and

user is at least 20 cm.

CAUTION

Closing the front panels
To ensure interference-free operation, keep the front panels of the module closed during

operation.

4.1

Connection modes and connection establishment

Note
Connection interrupted by GSM network provider
When using the GPRS service, remember that existing connections can be interrupted by

GSM network providers for maintenance purposes.

Connection modes

●

"GPRS direct" mode
There are no different connection modes in the "GPRS direct" mode.

●

"Telecontrol" mode
The CP can be configured for the following connection modes.
–

"Permanent" connection mode
There is a permanent TCP connection to the telecontrol server. Following connection

establishment, there is a permanent TCP connection to the telecontrol server even if

data is not transferred permanently.

–

"Temporary" connection mode
A connection is only established to the telecontrol server when required.

If a TCP connection is established, process data is sent as soon as the telecontrol

instructions are called on the CPU.

Содержание SIMATIC NET S7-1200



































































































Результаты поиска

Содержание SIMATIC NET S7-1200

Отзывы:

Похожие инструкции для SIMATIC NET S7-1200

Бренды по названию

Популярные бренды

Siemens SIMATIC NET S7-1200, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET S7-1200

Отзывы:

Похожие инструкции для SIMATIC NET S7-1200

Бренды по названию

Популярные бренды