manualshive.com logo in svg

Siemens SIMATIC NET RUGGEDCOM RST2228P, Руководство по установке, Страница: 18 / 60

Поделиться
Скачать
Siemens SIMATIC NET RUGGEDCOM RST2228P Скачать руководство пользователя страница 18

Installing the Device

2

This chapter describes how to install the device, including mounting the device,

connecting power, and connecting the device to the network.

DANGER

Electrocution hazard – risk of serious personal injury and/or damage to

equipment.

Before performing any maintenance tasks, make sure all power to the device has

been disconnected and wait approximately two minutes for any remaining energy

to dissipate.

WARNING

Radiation hazard – risk of serious personal injury.

This product may contain a laser system and is classified as a 

CLASS 1 LASER

PRODUCT

. Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

CAUTION

Burn hazard – risk of personal injury

The surface of the device may be hot during operation, or as a result of the ambient

air temperature.
Wear appropriate personal protective equipment and use caution when working

with or around the device.

NOTICE

Pollution Degree

This device must be installed in an environment with a minimum pollution degree of

PD2.

NOTICE

This product contains no user-serviceable parts. Attempted service by unauthorized

personnel shall render all warranties null and void.
Changes or modifications not expressly approved by Siemens AG could invalidate

specifications, test results, and agency approvals, and void the user's authority to

operate the equipment.

RUGGEDCOM RST2228P

Installation Manual, 07/2021, C79000-G8976-1403-13

9

Содержание SIMATIC NET RUGGEDCOM RST2228P





























































Отзывы:

Нет отзывов