Siemens SIMATIC NET RUGGEDCOM i800 Скачать руководство пользователя страница 32

Страница: 32 / 38

Certification

The RUGGEDCOM i800 device has been thoroughly tested to guarantee its

conformance with recognized standards and has received approval from recognized

regulatory agencies.

6.1

Approvals

This section details the standards to which the RUGGEDCOM i800 complies.

6.1.1

CSA

This device meets the requirements of the following Canadian Standards Association

(CSA) standards under certificates 2058468 (general safety) and 2068170

(hazardous locations):
•

CAN/CSA-C22.2 No. 62368-1-14

Information Technology Equipment – Safety – Part 1: General Requirements

•

CAN/CSA-C22.2 No. 0-M91

General Requirements - Canadian Electrical Code, Part II

•

CAN/CSA-C22.2 No. 14-05

Industrial Control Equipment

•

CAN/CSA-C22.2 No. 142-M1987

Process Control Equipment Industrial Products

•

CAN/CSA-C22.2 No. 213-M1987

Non-Incendive Electrical Equipment for Use in Class I, Division 2 Hazardous

Locations

•

UL 62368-1

Information Technology Equipment – Safety Part 1: General Requirements

•

ANSI/UL 508

Standard for Industrial Control Equipment

•

UL 916 4th Edition 2007

Standard for Energy Management Equipment

RUGGEDCOM i800

Installation Manual, 01/2021, C79000-G8976-1002-06

Содержание SIMATIC NET RUGGEDCOM i800







































Результаты поиска

Содержание SIMATIC NET RUGGEDCOM i800

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM i800

Бренды по названию

Популярные бренды

Siemens SIMATIC NET RUGGEDCOM i800, Руководство по установке

Результаты поиска

Содержание SIMATIC NET RUGGEDCOM i800

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM i800

Бренды по названию

Популярные бренды