Siemens SIMATIC NET PC PROFIBUS Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 36

Siemens SIMATIC NET PC PROFIBUS Скачать руководство пользователя страница 17

PROFIBUS Optical Bus Terminal (OBT)
Operating Instructions, 04/2016, C79000-G8976-C122-07

17

Commissioning

5

Note
Use the PROFIBUS OBT only as intended in these Operating Instructions.

Note
Pay particular attention to all warnings and notices relevant to safety.

WARNING

Operate the PROFIBUS OBT only with safety extra-low voltage complying with IEC 950 /

EN 60 950/VDE 0805 of m28.8 V (typ24 V). The power source must meet

the requirements of the UL/CSA approval for NEC Class 2 according to the National

Electrical Code (r) (ANSI / NFPA 70).

Note
Never look directly into the opening of the optical transmission diode. The emitted light beam

could endanger your eyes.

Note
Never connect the PROFIBUS OBT to a 100 V - 240 V power supply.

Note
Install the device so that the climatic limit values in the technical specifications are adhered

to.

Note
The RS-485 channel CH1 of the PROFIBUS OBT is isolated from the 24 V input. This

isolation relates to functionality and is not a safety measure.

«
...
15
16
17
18
19
...
»

Содержание SIMATIC NET PC PROFIBUS





































Отзывы:

Нет отзывов