Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Скачать руководство пользователя страница 79

Страница: 79 / 193

5 Display / WBM Configuration

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

5.2.11.4 Error

WBM: “Error” Tab − counting and evaluation of transmission errors

This page displays information on any errors that may have occurred and allows
diagnostics.

If you click on an entry, the Packet Error Statistics graphic is displayed. You then
see a configurable graphical representation of the counter value.

Parameter

Function

Port

LAN interface of the IE/AS-i LINK (1 or 2)

CRC

Number of packets with a valid length but bad checksum

Undersize

Number of packets that were too short with valid checksum

Oversize

Number of packets that were too long with valid checksum

Jabbers

Number of packets that were too long without valid checksum

Collisions

Number of collisions that occurred

Содержание SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Результаты поиска

Содержание SIMATIC NET IE/AS-INTERFACE LINK PN IO

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Руководство пользователя

Результаты поиска

Содержание SIMATIC NET IE/AS-INTERFACE LINK PN IO

Отзывы:

Бренды по названию

Популярные бренды