Siemens SIMATIC NET CP 443-5 Extended Скачать руководство пользователя | Manualshive

Страница: 29 / 46

background image

CP 443-5 Extended
Manual, 11/2018, C79000-G8976-C162-09

29

Installation and commissioning

3

3.1

Important notes on using the device

Safety notices on the use of the device

Note the following safety notices when setting up and operating the device and during all

associated work such as installation, connecting up or replacing the device.

3.1.1

Notes on use in hazardous areas

WARNING

EXPLOSION HAZARD
Do not open the device when the supply voltage is turned on.

WARNING

The device may only be operated in an environment with pollution degree 1 or 2 (see IEC

60664-1).

WARNING

The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a

Limited Power Source (LPS).
This means that only SELV / LPS complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1

must be connected to the power supply terminals. The power supply unit for the equipment

power supply must comply with NEC Class 2, as described by the National Electrical Code

(r) (ANSI / NFPA 70).
If the equipment is connected to a redundant power supply (two separate power supplies),

both must meet these requirements.

WARNING

EXPLOSION HAZARD
Do not connect or disconnect cables to or from the device when a flammable or

combustible atmosphere is present.

«
...
27
28
29
30
31
...
»

Содержание SIMATIC NET CP 443-5 Extended















































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC NET CP 443-5 Extended

Бренд: Barco Страницы: 100

Бренд: Harman Kardon Страницы: 66

Бренд: QSC Страницы: 28

xCORE-200 Multi-channel Audio board

Бренд: XMOS Страницы: 112

Бренд: Q-See Страницы: 2

Бренд: IBA Страницы: 29

Бренд: Direct IP Страницы: 76

Бренд: Alesis Страницы: 61

SuperServer 5019S-L

Бренд: Supermicro Страницы: 61

Бренд: Time domain Страницы: 64

Бренд: Endace Страницы: 51

Power Control Processor

Бренд: ETC Страницы: 64

Core 2 Quad Q9400

Бренд: Intel Страницы: 2

F-Tile SDI II Intel Agilex

Бренд: Intel Страницы: 39

Бренд: East Coast Datacom Страницы: 19

PSoC 4 S Series

Бренд: Cypress Страницы: 4

Бренд: Microtek Страницы: 25

AH10EN-5A Series

Бренд: Delta Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды