Siemens SIMATIC NET CP 343-1 Скачать руководство пользователя страница 37

Страница: 37 / 78

Installation, connecting up and commissioning

5.2 Installing the CP, connecting power and ground

CP 343-1
Manual, 12/2018,

C79000−G8976−C201

-08

WARNING

Suitable cables for temperatures in excess of 70 °C
If the cable or conduit entry point exceeds 70°C or the branching point of conductors

exceeds 80°C, special precautions must be taken. If the device is operated at ambient

temperatures above 50°C, the permitted temperature range of the selected cable must be

suitable for the temperatures actually measured.

WARNING

Protection against transient voltage surges
Provisions shall be made to prevent the rated voltage from being exceeded by transient

voltage surges of more than 40%. This criterion is fulfilled, if supplies are derived from

SELV (Safety Extra-Low Voltage) only.

5.2

Installing the CP, connecting power and ground

Note
Pulling/plugging
Pulling/plugging the CP when the power is on is not permitted.

You should also remember that by removing a module from the rack, all modules on the

other side of it will be disconnected from the CPU.

Содержание SIMATIC NET CP 343-1















































































Результаты поиска

Содержание SIMATIC NET CP 343-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 343-1

Бренды по названию

Популярные бренды

Siemens SIMATIC NET CP 343-1, Руководство пользователя

Результаты поиска

Содержание SIMATIC NET CP 343-1

Отзывы:

Похожие инструкции для SIMATIC NET CP 343-1

Бренды по названию

Популярные бренды