Siemens SIMATIC NET CP 243-1 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 142

Siemens SIMATIC NET CP 243-1 Скачать руководство пользователя страница 45

Installation and commissioning

2.2 Installation and electrical connections

CP 243-1
Operating Instructions, 03/2012, C79000-G8976-C244-02

45

WARNING

Protection against transient voltage surges
Take measures to prevent transient voltage surges of more than 40% of the rated voltage.

This is the case if you only operate devices with SELV (safety extra-low voltage).

2.2

Installation and electrical connections

Installation

You can install the devices of the S7-200 series either in a control panel or on a DIN rail. You

can arrange the modules both horizontally and vertically. The S7-200 CPU and the

expansion modules are designed for natural heat dissipation by convection. For this reason,

leave a clearance of at least 25 mm above and below the devices so that the heat is free to

escape. Long operating times at maximum ambient temperatures and maximum loads will

shorten the lifespan of the electrical components of the device.
When using firmware version on the CPU of 1.2 or higher, the CP 243-1 can be installed in

any one of 7 positions in an S7-200 system.

Wiring

WARNING

If you attempt to install or remove the CP 243-1 or other devices while they are on, you may

receive an electric shock or the devices may not work properly.
If the power for the CP 243-1 and all connected devices is not switched off while the

devices are being installed/removed, this may cause injury and/or property damage.
Take all necessary safety precautions and make sure that the power for the S7-200 and the

CP 243-1 is turned off before you begin wiring.

General guidelines

Below, you will find some general guidelines for wiring your programmable controller:
●

Make sure that you comply with all valid and binding standards when you wire up your

CP 243-1. When installing and operating the device, keep to the relevant national and

regional regulations. Ask your local authorities for the standards and regulations that

apply to your specific situation.

●

Only wire up the S7-200 CPU and the CP 243-1 when the power is turned off!

«
...
43
44
45
46
47
...
»

Содержание SIMATIC NET CP 243-1















































































































































Отзывы:

Нет отзывов