Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 62

Страница: 62 / 82

Connection

6.7 Replacing a CLP

SCALANCE WxM766

Operating Instructions, 03/2022, C79000-G8976-C617-03

6.7

Replacing a CLP

Position

The CLP slot is at the top of the device enclosure under a cover, see Reset button

(Page 33).

①

M3 screws (Torx T10)

②

Slot cover

③

CLP

Removing a CLP

Note
Loss of the configuration

The reset button is located directly beside the slot for the CLP. The reset button cannot

be used to remove the CLP.
If you press and hold down the reset button you reset all the settings of the device to the

factory defaults.

To remove a CLP from the device, follow the steps below:
1.

Turn off the power to the device.

Loosen the screws M3

①

with a Torx screwdriver T10 and remove the slot cover

②

As an alternative, you can loosen only one of the screws

①

and swivel the slot cover

②

to the side.

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды