Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 59

Страница: 59 / 82

Connection

6.5 Digital input/output

SCALANCE WxM766
Operating Instructions, 03/2022, C79000-G8976-C617-03

Note
Terminating resistor

Any connections that are not in use must be fitted with a terminating resistor, see

Accessories (Page 21).

An antenna must always be connected to the antenna connector as soon as the WLAN

interface is switched on. Otherwise, there may be transmission disruptions.

Note
Cabinet installation

When installing the SCALANCE WxM766-1 in a cabinet, you need to use detached

antennas. Use a suitable flexible connecting cable for a connection between SCALANCE

WxM766-1 and a detached antenna. You will find detailed information in the section

Accessories (Page 21).

NOTICE
UL approval only for use in buildings

Within the area of authority of the NEC and CEC, the SCALANCE WxM766-1 devices

and the antennas connected to them may only be used in a closed building. For this

reason, do not lead antennas into the outdoor area if you need to meet UL or CSA

requirements.

6.5

Digital input/output

The device features a digital input and output (M12 A-coded).

CAUTION

Damage due to voltage being too high or too low

The voltage at the digital input/output must not exceed 30 VDC and not fall below -30

VDC, otherwise the digital input/output will be destroyed.

Note
Interference pulse

To avoid evaluating an interference pulse, the pulse for the signal 1 (TRUE / HIGH) must

be at least 200 ms.

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды