Siemens SIMATIC MP 270B Скачать руководство пользователя страница 213 | Manualshive

Страница: 213 / 274

Siemens SIMATIC MP 270B Скачать руководство пользователя страница 213

Maintenance/Service

11.2 Replacing the optional backup battery

TP 270, OP 270, MP 270B (WinCC flexible)
Operating Instructions, Edition 03/2004, 6AV6691-1DD01-0AB0

11-3

11.2

Replacing the optional backup battery

Function of the backup battery

An optional backup battery is available for the HMI device. The battery ensures that in the

event of a power failure, the HMI device's internal hardware clock continues to run.
Under normal operating conditions, the battery has a service life of approx. four years. It is

not supplied with the HMI device.

Supply source

The battery can be ordered from the Siemens spare parts service. It is shipped ready for

installation with a cable and connector. Please refer to the Siemens Catalog ST80 for the

order number.

Procedure

Caution
Change the battery while power is still being supplied to ensure the internal hardware clock

continues to run.
The battery must be changed by a properly qualified person.
Before replacing the battery, refer to the ESD Guidelines.

1. Unplug the battery cable connector from the two-pin socket in the HMI device.
2. In the case of the MP 270B 10", TP 270 10" or OP 270 10", the battery is normally

secured at the back of the HMI device with two cable ties, In the case of the MP 270B 6",

TP 270 6" or OP 270 6", one cable tie is used. Cut the cable ties, using pliers for

instance, and remove the empty battery.

3. In the case of the MP 270B 10", TP 270 10" or OP 270 10", secure the battery at the back

of the HMI device with two cable ties. In the case of the MP 270B 6", TP 270 6" or OP

270 6", use one cable tie.

4. Insert the battery lead connector back into the socket. The plug is coded to prevent

reversed poling.

General information

Please observe the following safety notes to ensure correct handling and disposal of lithium

batteries:

«
...
211
212
213
214
215
...
»

Содержание SIMATIC MP 270B



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды