manualshive.com logo in svg

Siemens SIMATIC IPC677E, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMATIC IPC677E Скачать руководство пользователя страница 35

 

Mounting and connecting the device 

 

3.1 Preparing for mounting 

SIMATIC IPC677E 
Operating Instructions, 04/2019, A5E45117996-AA 

35

 

3.1.2

 

Checking the delivery package 

 

 

WARNING 

Electric shock and fire hazard due to damaged device 
Damaged devices due to improper storage or transport may lead to personal injury and/or 

substantial damage to equipment. 

•

 

You must observe the warnings in "Note on transport and storage (Page 27)". 

 

Procedure 

1.

 

Check the packaging and package contents for visible transport damage.  
If any transport damage is present at the time of delivery, lodge a complaint at the 

shipping company in charge. Have the shipper confirm the transport damage 

immediately. 

2.

 

Unpack the device at its installation location. 

3.

 

Keep the original packaging in case you have to transport the unit again. 

4.

 

Check the Scope of delivery (Page 33) and any accessories you may have ordered for 

completeness and damage. Please inform the delivery service immediately if the package 

contents are incomplete or damaged or do not correspond with your order. Fax the 

enclosed form "SIMATIC IPC/PG Quality Control Report".  

5.

 

Please keep the enclosed documentation in a safe place. It belongs to the device. You 

need the documentation when you commission the device for the first time. 

6.

 

Write down the Identification data of the device (Page 36) identification data of the device. 

Содержание SIMATIC IPC677E































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды