Siemens SIMATIC IPC677E Скачать руководство пользователя

Страница: 37 / 158

Mounting and connecting the device

3.1 Preparing for mounting

SIMATIC IPC677E
Operating Instructions, 04/2019, A5E45117996-AA

3.1.4

Mounting positions

NOTICE
"Open Equipment" IEC/EN/UL61010
The device is designed for use as a programmable controller, OpenType according to

IEC/EN/UL 61010-2-201. The installation of the device in a fire protection housing in

accordance with IEC/EN/UL 61010-2-201 is therefore a mandatory requirement for

approval or operation.

The following mounting positions are permitted for the device.
For information on the maximum permissible ambient temperatures during operation, refer to

section "Ambient conditions (Page 115)".

Mounting positions according to UL61010

Note
Operation in closed rooms
The device is approved for operation in closed rooms only. Note the Ambient conditions

(Page 115).

Mounting in horizontal format

Note
Mounting precautions

•

The total power for USB and PCI/PCIe expansions cannot exceed 30 W.

Содержание SIMATIC IPC677E































































































































































Результаты поиска

Содержание SIMATIC IPC677E

Отзывы:

Похожие инструкции для SIMATIC IPC677E

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC677E, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC677E

Отзывы:

Похожие инструкции для SIMATIC IPC677E

Бренды по названию

Популярные бренды