Siemens SIMATIC IPC627E Скачать руководство пользователя

Страница: 38 / 164

Installing and connecting the device

3.1 Preparing for installation

SIMATIC IPC627E

Operating Instructions, 12/2018, A5E44297201-AA

3.1.3

Identification data of the device

The device can be clearly identified with the help of this identification data in case of repairs

or loss.
The following illustrations are examples. The data of your device may differ from the data in

these examples.

Nameplate

The following image shows the nameplate on the SIMATIC IPC627E as an example.

COA label

The COA label (Certificate of Authenticity) is located on the rear of the device.

Note
The COA label is only available on devices shipped with an installed Microsoft® Windows®

operating system.

Example of COA label for the Microsoft® Windows® 10 operating system:

Содержание SIMATIC IPC627E





































































































































































Результаты поиска

Содержание SIMATIC IPC627E

Отзывы:

Похожие инструкции для SIMATIC IPC627E

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC627E, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC627E

Отзывы:

Похожие инструкции для SIMATIC IPC627E

Бренды по названию

Популярные бренды